Top 9 Roper Electric Dryer Heating Element

This is a dryer heating element replacement for Whirlpool, Kenmore, Sears, Maytag, KitchenAid, Magic Chef, Amana, Admiral, Norge, Estate, Inglis, Roper, and Crosley. If your dryer does not heat first, check for a blown thermal fuse on the blower housing before replacing the heating element. In most cases, the heating element will have a break in the element if defective. Rated 240 volts and 5400 watts. It replaces 279838 PS334313 AP3094254 3398064 3403585 8565582 AH334313 EA334313, EED4400WQ0. Manufacturers’ part numbers are solely for identification. All materials supplied by us are our replacements for manufacturers’ parts. All product and company names are trademarks or registered trademarks of their respective holders. Use of them does not imply any affiliation with or endorsement by them.

How To Test 279838 Heating Element:
To test your heating element you will need to first remove the heating element from the dryer. With the element removed from the dryer, do a visual inspection of the element. Often times you will be able to see a break in the heating coil. Sometimes it even helps to grab each section of the coil and wiggle it to make sure there isn’t a break in it. If you can’t see a break in the coil, then you will need an Ohm meter or Multi-Meter to test the heating element. Place one probe on each terminal of the heating element, you should get a reading of approximately 10 ohms on a good element. If you get no resistance, then the element is damaged and need to be replaced.

279838 Dryer heating element assembly – 5400 watt 240 volt. Transfer the high limit thermostat from your old heating element over to the new element. Don’t settle for lower quality heating elements.
Replaces 3403585 279837 8565582 3398064 3403585 AP3094254 W10724237 279838A 279838VP

279816 Thermal Fuse & Thermostat Kit – Dryer thermal fuse (thermal cut-off) 309 degrees and high limit thermostat 250 degrees kit – Wiring is used if your old high limit thermostat has one terminal that presses onto the heating element. Includes thermal fuse, thermostat, screws, wiring kit, and instructions. Make sure to check your dryer vent for any restrictions.
Replaces 3399848 3977393 2651 AP3094244 PS334299 EAP334299

3392519 Thermal Fuse – Dryer non resettable thermal fuse, two 3/16″ wire terminals. This fuse is located on the blower housing next to the blower fan. If the dryer overheats, the thermal fuse blows to cut off power to the dryer and/or stop the dryer from running.
Replaces WP3392519 3388651 694511 80005 ET401 G4AP0500 3392519

KONDUONE always offer the best customer service to his customers.If you have any problem about your order,please feel free to contact us.

Package includes:
1 * 3387747 Heating Element
1 * 279816 Thermostat Kit
1 * 3392519 Thermal Fuse

3387747 heating element fits later model electric clothes dryers and has 2 5/16″ terminals. Replaces part numbers 80003, 8527865, AP2947033, AP6008281, PS344597, and PS11741416.
3392519 thermal fuse part is a one-time use thermal fuse which attaches to the blower wheel housing of your clothes dryer. It cannot be re-set and must be replaced when continuity between the pins is no longer present. Terminal size is 3/16″. Replaces part numbers AP3132867, 2986, 3388651, 694511, 80005, AH345113, EA345113, ET401, PS345113.
279816 dryer thermal cut-off kit includes one high limit thermostat with a limit of 250 degrees Fahrenheit, and one thermal cut-off fuse (309 degrees). Replaces part numbers AP3094244, 2651, 3399848, 3977393, AH334299, EA334299, PS334299.
This kit also includes flat heaters with jumper wires.
All parts work with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.